产品名称：Y-C-OFFSET测试图卡(IEC 61146)TE217 爱莎ESSER测试卡 3nh定制

 
Luminance-Chrominance-Offset (Y-C-Offset) describes the temporal difference between the luminance and chrominance channel. The temporal difference has to be measured between points of 50 percent amplitude of luminance and chrominance transition. Both signals mus come from the same test pattern.
Measuring procedure for PAL / NATSC
The measurement setup has to be on a par with figure 2 below.  

The test chart consists of a green cross on gray background (20% transparency). The luminance signal E'Y and the chrominance signals R'(R-Y) and R'(B-Y) are generated with a calibrated demodulator. With the aid of a two-beam-oscilloscope the time difference is measured. The Y-C-Offset of the demodulator has to be measured and specified with the results.
Horizontal Y/C-Offset
Line M has to be selected (see figure 2, 2a, 2b) and, shown in figures 2d and 2e, displayed increased on the scope. The time difference tdH in ns has to be measured between the 50% points of level. When reading out the luminance signal Y and the chrominance signal C separately, the measurement of this signals has to be realized without demodulation of the chrominance signal (see figure 2m, 2n, 2p, 2r, 2s). This method only applies to PAL and NTSC. The rise time t1 and the fall time t2 of the chrominance signals E'(R-Y) and E'(B-Y) must be measured (see figure 2f).
Vertical Y/C-Offset
With the aid of the scope a half picture is chosen (see figure 2d and 2e) and displayed increased (see figure 2k and 2l). The time difference tdv between the 50% points of the luminance signal E'Y and the chrominance signals E'(R-Y) and E'(B-Y) has to be measured and shown in picture line periods (see figure 2k and 2l).
Presentation of results
Time difference, rise edge and fall edge have to be described with luminace edge for reference in the following modality:
horizontal offset tdH in ns (figures 2d and 2e)
vertical offset tdv in TV lines (figures 2k and 2l)
chrominance rise edge t1 in ns (figure 2f)
chrominance fall edge t2 in ns (figure 2f)
Y/C-Offset of the demodulator in ns (figure 2f)
Note:
Due to the small bandwith of the chrominace channel, the rise edge of the chrominance signal is generated before the rise edge of the luminance signal (negative offset) and the fall edge after the fall edge of the luminance signal (positive offset). The time difference between both is taken for main offset, which can be positive or negative. 

• 1、厂家货源**

   官方直售，公司生产周期短，出厂严格检测，货品品质保障，可通过国家计量院计量。

• 2、关于尺码

   机身和包装尺寸为手动测量，由于测量工具和测量方法不同的因素，会存在1cm误差，但是不用影响运输和使用。

• 3、关于颜色

   本店产品都是实拍图片，但是由于不同显示器分辨不同以及色温和对比度差异有所不同。 

• 4、关于客服

   可以通过阿里旺旺随时联系我们，如果旺旺回复不及时，也可以拨打我们的专线电话  顾工：13310057376 （技术与销售一体，直达客户需求）

• 5、关于售后

   我们将提供完整的售后服务，包括15天退货，**保证，交期保障等等。

• 6、关于发货

  本店根据货物及客户需求，尽可能选择快捷方便的物流运输服务，一般情况发顺丰快递！